| 1. | Multivariable control system
多变量控制系统 |
| 2. | Load / pressure plant of turbine - generator unit is a complicated multivariable control plant
火电厂单元机组负荷/汽压对象是一个相对复杂的多变量控制对象。 |
| 3. | Meanwhile , multivariable control can provide better control result than single - variable control in engine acceleration process
发动机模型越真实，约束条件越合理，所得的加速过程计算结果就越好。 |
| 4. | Numerical simulations confirm the strategy ' s validity and feasibility . this strategy provides an effective solution to other nonlinear multivariable control systems as well
仿真实验证明，该策略是有效和可行的，并为其他非线性多变数系统的控制提供了有效方法。 |
| 5. | Combined with these bound establishing methods , a new integrated mv benchmarking bounds performance assessment theory system of multivariable control system is constituted
几种建界方法相互结合，形成一套完整的、基于最小方差基准界的多变量控制系统性能评价理论体系。 |
| 6. | Simulations for 2 * 2 multivariable control systems parameter adjustment are carried out . the results show that the proposed optimal adjustment strategy and the related soft are valid . 3
对2 2多变量控制系统的pid参数优化整定进行了仿真研究，结果表明，所开发的pid参数优化整定软件是有效的。 |
| 7. | Definition of the multivariable control strategy has been provided in sufficient detail with emphasis on the regenerator control , cracking conversion control , pressure balance control , main fractionator bottom control and cracking yields control
从烧焦控制、裂化苛刻度控制、压力平衡控制、分馏塔底控制和裂化产率优化控制等五方面详细论述了反应-再生系统的控制策略。 |
| 8. | When several coke ovens are connected in parallel , there are many external disturbance factors , as well as complex coupling relations , so the discharge header pressure system of coke oven is a complex multivariable control system and there is no mathematical model up to now
在多座焦炉并联生产条件下，集气管压力控制对象存在复杂的耦合关系，且尚无精确的数学模型，这就给集气管压力控制系统的设计带来困难，难以实现精确的控制。 |
| 9. | Summarizes the design and develop ways of monitoring and fault diagnosis systems based on pca for multivariable control system . introduces the main statistical variables , multivariate control charts and the analysis ways of statistical variables . then this paper takes a model of continuous process for example , to show and analysis the result of fault diagnosis based on pca
概述和总结了基于主元分析的多变量控制系统故障监测与诊断系统设计思想，分析了主要统计量、控制图以及数据基本分析处理方法，并以一个连续生产过程模型为例，阐述了故障诊断模型的建立过程以及诊断结果分析。 |
| 10. | And this algorithms have been proved to be valid by computer analogize for two different model . after a detailed analysis of the glass furnace , put award a method of disassemble multivariable control : the upper levels use fuzzy supervise control , provide reference signal for lower level ; the lower level select and use a modified self - regulating fuzzy controller or a double closed - loop controller for time - sluggish system
在分析窑炉特性的基础上，以温度系统为例，根据其被控参数多、大滞后、非线性等特点，提出分层分区的智能控制策略：上层采用模糊监督控制器，为下层提供参考信息，下层根据控制要求及被控对象特性分别采用了一种改进的自校正控制算法和一种适合于滞后过程的双环模糊控制器。 |
